Queclink GV300N

Queclink GV300N is a compact GPS tracker designed for a wide variety of vehicle tracking applications. Its built-in GPS receiver has superior sensitivity and fast time to first fix.

Title Name Description Properties
Analog Input analog_input Analog Input Port configuration fuel: Fuel Analog Input

input1: Analog Input #1

input2: Analog Input #2

change_threshold: Change Threshold
Backend Server Setup backend_server Configure the backend server information host: Host

port: Port

heartbeat: Heartbeat Interval

buffer_mode: Buffering mode

report_mode: Report Mode

sack_enable: Server ACK
CAN Data Setup can_gv Configure the CAN data sending and its content mode: Enable CAN Report

ign_on: Ignition ON CAN Data Report

report: CAN Data Report Composition

ign_off: Ignition OFF CAN Data Report

ignition_event: Report On Ignition ON/OFF
Device Parameters config Configure global parameters of the device. agps: AGPS Mode enable

led_mode: LEDs working mode

odometer: Odometer

pwr_mode: Power saving mode

inf_report: Information Report

pin15_mode: Pin 15 mode

device_name: Device Name

gps_on_need: GPS On Need

new_password: New Device Password

gps_lost_time: GPS lost time

location_by_call: Location By Call
Device Information device_info Generic device information. name: Device Name

protocol: Protocol Version
Device Password device_password Device password, used to execute commands. password: Password
Events events Configure events that will cause reporting a message to the backend server. ant_event: External GPS antenna status changed

bpl_event: Backup battery is low

btc_event: Backup battery started charging

igl_event: Send GPS position when ignition on/off

ign_event: Report ignition on/off events

mpf_event: Main power supply disconnected

mpn_event: Main power supply connected

pdp_event: Report GPRS connection established

pfa_event: Power off event

pna_event: Power on event

rtl_event: Report GPS position when power off

stc_event: Backup battery stopped charging

stt_event: Device motion state changed

ufs_event: UFSxxx fault code
External Power Supply Alarm ext_power_alarm External Power Supply Alarm configuration mode: Mode

sync: Sync With FRI

output: Output

debounce: Debounce Time

max_threshold: Max Threshold

min_threshold: Min Threshold
Fixed Report fixed_report_gv Fixed Report Configuration: GPS Tracking Mode Setup mode: Working Mode

corner: Corner Report

time_range: Time Range

without_gps: Reporting Without GPS

igf_interval: Engine Off Position Reporting

extended_report: Extended Fixed Report Content
GSM Reports gsm_reports Control how or when to report cells’ information. mode: GSM Reports Mode

reports: Select reports
Digital Inputs inputs Digital inputs control input1: Input #1

input2: Input #2

input3: Input #3

ignition: Ignition Input
GSM Network Setup network_gsm Configure the GPRS/WCDMA/3G parameters in GSM networks apn: APN

password: APN Password

username: APN Username
Reboot reboot Reboot the terminal.
Report Composition report Configure the composition of report message and GPS information. alt_enable: Altitude

gsm_enable: GSM tower data

mil_enable: Mileage

dname_enable: Device name

speed_enable: Speed

stime_enable: Send time

course_enable: Course
Reset Parameters reset_params Reset all parameters (except connectivity settings) to factory defaults.
Tow Alarm tow_alarm Tow Alarm configuration output: Output

rest_dur: Stillness Timeout

engine_off: Engine Off timeout

motion_dur: Motion Timeout

tow_enable: Tow Alarm

motion_sens: Motion Sensor Sensitivity

tow_timeout: Tow Alarm Timeout

tow_interval: Tow Interval
UART Serial Port uart_serial_port_gv Configure the serial port mode: Working Mode

sleep: Sleep Enable

baudrate: Baudrate

data_bits: Data Bits

stop_bits: Stop Bits

parity_bits: Parity Bits

wakeup_input: Enable Wakeup Input